MIPS代写 Lab 1: Pipeline MIPS Processor

Lab 1: Pipeline MIPS Processor

In this Lab assignment, you will implement an cycle-accurate simulator for a 5-stage pipelined MIPS processor in C++. The simulator supports a subset of the MIPS instruction set and should model the execution of each instruction with cycle accuracy.

The MIPS program is provided to the simulator as a text file “imem.txt” file which is used to initialize the Instruction Memory. Each line of the file corresponds to a Byte stored in the Instruction Memory in binary format, with the first line at address 0, the next line at address 1 and so on. Four contiguous lines correspond to a whole instruction. Note that the words stored in memory are in “Big-Endian” format, meaning that the most significant byte is stored first.

The Data Memory is initialized using the “dmem.txt” file. The format of the stored words is the same as the Instruction Memory. As with the instruction memory, the data memory addresses also begin at 0 and increment by one in each line.

The instructions that the simulator supports and their encodings are shown in Table 1. Note that all instructions, except for “halt”, exist in the MIPS ISA. The MIPS Green Sheet defines the semantics of each instruction.

Pipeline Structure

Your MIPS pipeline has the following 5 stages:

1. Fetch (IF): fetches an instruction from instruction memory. Updates PC.
2. Decode (ID/RF): reads from the register RF and generates control signals required in

   subsequent stages. In addition, branches are resolved in this stage by checking for the

   branch condition and computing the effective address.

3. Execute (EX): performs an ALU operation.
4. Memory (MEM): loads or stores a 32-bit word from data memory.
5. Writeback (WB): writes back data to the RF.

Your simulator can make use of the same RF, IMEM and DMEM classes that you used for Lab0. Complete implementations of these classes are provided for you in the skeleton code.

Note that we have not defined an ALU class since, for this lab, the ALU is simple and only needs to perform adds and subtracts.

Each pipeline stages takes inputs from flip-flops. The input flip-flops for each pipeline stage are described in the tables below.

IF Stage Input Flip-Flops

ID/RF Stage Input Flip-Flops

EX Stage Input Flip-Flops

MEM Stage Input Flip-Flops

WB Stage Input Flip-Flops

Dealing with Hazards

Your processor must deal with two types of hazards.

1. RAW Hazards: RAW hazards are dealt with using either only forwarding (if possible) or,

   if not, using stalling + forwarding. You must follow the mechanisms described in Lecture

   6 to deal RAW hazards.

2. Control Flow Hazards: You will assume that branch conditions are resolved in the

   ID/RF stage of the pipeline. Your processor deals with beq instructions as follows:

   1. Branches are always assumed to be NOT TAKEN. That is, when a beq is fetched

      in the IF stage, the PC is speculatively updated as PC+4.

   2. Branch conditions are resolved in the ID/RF stage. To make your life easier,

      will ensure that every beq instruction has no RAW dependency with its previous two instructions. In other words, you do NOT have to deal with RAW hazards for branches!

   3. Two operations are performed in the ID/RF stage: (i) Read_data1 and Read_data2 are compared to determine the branch outcome; (ii) the effective branch address is computed.
   4. If the branch is NOT TAKEN, execution proceeds normally. However, if the branch is TAKEN, the speculatively fetched instruction from PC+4 is quashed in its ID/RF stage using the nop bit and the next instruction is fetched from the effective branch address. Execution now proceeds normally.

The nop bit

The nop bit for any stage indicates whether it is performing a valid operation in the current clock cycle. The nop bit for the IF stage is initialized to 0 and for all other stages is initialized to 1. (This is because in the first clock cycle, only the IF stage performs a valid operation.)

In the absence of hazards,, the value of the nop bit for a stage in the current clock cycle is equal to the nop bit of the prior stage in the previous clock cycle.

However, the nop bit is also used to implement stall that result from a RAW hazard or to quash speculatively fetched instructions if the branch condition evaluates to TAKEN. See Lecture 6 slides for more details on implementing stalls and quashing instructions.

The HALT Instruction

The halt instruction is a “custom” instruction we introduced so you know when to stop the simulation. When a HALT instruction is fetched in IF stage at cycle N, the nop bit of the IF stage

in the next clock cycle (cycle N+1) is set to 1 and subsequently stays at 1. The nop bit of the ID/RF stage is set to 1 in cycle N+1 and subsequently stays at 1. The nop bit of the EX stage is set to 1 in cycle N+2 and subsequently stays at 1. The nop bit of the MEM stage is set to 1 in cycle N+3 and subsequently stays at 1. The nop bit of the WB stage is set to 1 in cycle N+4 and subsequently stays at 1.

At the end of each clock cycle the simulator checks to see if the nop bit of each stage is 1. If so, the simulation halts. Note that this logic is already implemented in the skeleton code provided to you.

What to Output

Your simulator will output the values of all flip-flops at the end of each clock cycle. Further, when the simulation terminates, the simulator also outputs the state of the RF and Dmem. The skeleton code already prints out everything that your simulator needs to output. Do not modify this code.

Testbenches and Grading

Test inputs for your simulator are in the form of “imem.txt” and “dmem.txt” files, and the expected outputs are in the form of “RFresult.txt”, “dmemresult.txt” and “stateresult.txt” files.

To assist you in checking your code, we will provide sample input and output files to you. However, your code will be graded on our own test inputs.

You are encouraged to develop your code in steps. A rough time frame for how long each step would take is given below.

1. Step 1: your simulator should be able to handle addu, subu, lw and sw instructions without any RAW hazards. (1 Week)
2. Step 2: in addition, your simulator should be able to handle addu, subu, lw and sw instructions with RAW hazards. (1 Week)
3. Step 3: finally, enhance your simulator to handle beq instructions.

The grading scheme that we will use to test your code is:

• ●  Code compiles and executes without crashing on all test inputs [10 Points]
• ●  Code handles inputs with only addu, subu, lw and sw instructions without any RAW

  hazards [30 Points]

• ●  Code handles inputs with only addu, subu, lw and sw instructions with RAW hazards. [30

  Points]

• ●  Code handles all test inputs including those with beq instructions. [30 Points]