Penn State University School of Electrical Engineering and Computer Science Page 1 of 5 CMPEN 331 – Computer Organization and Design,
Chapter 2 Review Questions
1. For the following MIPS assembly instructions above, what is a corresponding C statement? f, g, h and i are assigned to registers $s0, $s1, $s2 and $s3, respectively
add f,g,h add f,i,f
Copyright By PowCoder代写 加微信 powcoder
2. For the following C statement, what is the corresponding MIPS assembly code? Assume that the variables i, and j are assigned to registers $s3, and $s4, respectively. Assume that the base address of the arrays A and B are in registers $s6 and $s7, respectively.
B[8] = A[i − j];
5 Translate the following MIPS code to C. Assume that the variables f, g, h, i, and j are assigned to registers $s0, $s1, $s2, $s3, and $s4, respectively. Assume that the base address of the arrays A and B are in registers $s6 and $s7, respectively.
addi $t0, $s6, 4
add $t1, $s6, $0
sw $t1, 0($t0)
lw $t0, 0($t0)
add $s0, $t1, $t0
6 Assume that registers $s0 and $s1 hold the values 0x80000000 and 0xD0000000, respectively.
a. What is the value of $t0 for the following assembly code?
add $t0, $s0, $s1
b. Is the result in $t0 the desired result, or has there been overflow?
Penn State University School of Electrical Engineering and Computer Science Page 2 of 5
c. For the contents of registers $s0 and $s1 as specified above, what is the value of $t0 for the following assembly code?
sub $t0, $s0, $s1
d. Is the result in $t0 the desired result, or has there been overflow?
7 Provide the type and hexadecimal representation of following instruction: sw $t1, 32($t2)
8 Find the MIPS instructions that extracts bits 16 down to 11 from register $t0 and uses the value of this field to replace bits 31 down to 26 in register $t1 without changing the other 26 bits of register $t1.
10. Assume $t0 holds the value 0x00101000. What is the value of $t2 after the following instructions?
9 For the following C statement, write a sequence of MIPS assembly instructions that does the identical operation. Assume $t1 = A, $t2 = B, and $s1 is the base address of C.
A = C[0] << 4;
slt $t2, $0, $t0
bne $t2, $0, ELSE
ELSE: addi $t2, $t2, 2
11. Write the MIPS assembly code that creates the 32-bit constant
0010 0000 0000 0001 0100 1001 0010 0100two
and stores that value to register $t1.
Penn State University School of Electrical Engineering and Computer Science Page 3 of 5
1. For the following MIPS assembly instructions above, what is a corresponding C statement? f, g, h and i are assigned to registers $s0, $s1, $s2 and $s3, respectively
add f,g,h add f,i,f
2. For the following C statement, what is the corresponding MIPS assembly code? Assume that the variables i, and j are assigned to registers $s3, and $s4, respectively. Assume that the base address of the arrays A and B are in registers $s6 and $s7, respectively.
B[8] = A[i − j];
sub $t0, $s3, $s4
sll $t0, $t0, 2
add $t1, $s6, $t0
lw $t2, 0($t1)
sw $t2, 32($s7)
3. Assume that registers $s0 and $s1 hold the values 0x80000000 and 0xD0000000, respectively.
a. What is the value of $t0 for the following assembly code?
add $t0, $s0, $s1
0x50000000
b. Is the result in $t0 the desired result, or has there been overflow?
Penn State University School of Electrical Engineering and Computer Science Page 4 of 5
c. For the contents of registers $s0 and $s1 as specified above, what is the value of $t0 for the following assembly code?
sub $t0, $s0, $s1
d. Is the result in $t0 the desired result, or has there been overflow?
no overflow
4. Provide the type and hexadecimal representation of following instruction: sw $t1, 32($t2)
i-type, 0xAD490020
5. Translate the following MIPS code to C. Assume that the variables f, g, h, i, and j are assigned to registers $s0, $s1, $s2, $s3, and $s4, respectively. Assume that the base address of the arrays A and B are in registers $s6 and $s7, respectively.
addi $t0, $s6, 4
add $t1, $s6, $0
sw $t1, 0($t0)
lw $t0, 0($t0)
add $s0, $t1, $t0
f = 2*(&A);
6. Find a sequence of MIPS instructions that extracts bits 16 down to 11 from register $t0 and uses the value of this field to replace bits 31 down to 26 in register $t1 without changing the other 26 bits of register $t1.
srl $t0, $t0, 11
sll $t0, $t0, 26
ori $t2, $0, 0x03ff
sll $t2, $t2, 16
ori $t2, $t2, 0xffff
Penn State University School of Electrical Engineering and Computer Science Page 5 of 5 and $t1, $t1, $t2
or $t1, $t1, $t0
lw $t3, 0($s1)
sll $t1, $t3, 4
8. Assume $t0 holds the value 0x00101000. What is the value of $t2 after the following instructions?
7. For the following C statement, write a minimal sequence of MIPS assembly instructions that does the identical operation. Assume $t1 = A, $t2 = B, and $s1 is the base address of C.
A = C[0] << 4;
slt $t2, $0, $t0
bne $t2, $0, ELSE
ELSE: addi $t2, $t2, 2
9. Write the MIPS assembly code that creates the 32-bit constant
0010 0000 0000 0001 0100 1001 0010 0100two
and stores that value to register $t1.
Generally, all solutions are similar:
lui $t1, top_16_bits
ori $t1, $t1, bottom_16_bits
程序代写 CS代考 加微信: powcoder QQ: 1823890830 Email: powcoder@163.com