Microsoft Word – Quiz for Chapter 4 with Solutions.doc
Date:
Quiz for Chapter 4 The Processor3.10
Not all questions are of equal difficulty. Please review the entire quiz first and then
budget your time carefully.
Name:
Course:
Solutions in RED
1. [6 points] For the MIPS datapath shown below, several lines are marked with “X”. For each one:
• Describe in words the negative consequence of cutting this line relative to the working,
unmodified processor.
• Provide a snippet of code that will fail
• Provide a snippet of code that will still work
(1) Cannot write to register file. This means that R-type and any instruction with write back to register
file will fail. An example of code snippet that would fail is:
add $s1, $s2, $s3
An example of a code snippet that will not fail is:
sw $s1, 0($s2)
Name: _____________________
Quiz for Chapter 4 The Processor
Page 2 of 30
(2) Forwarding of the first operand fails. An example of code snippet that would fail is:
add $s1, $t0, $t1
add $s1, $s1, $s1
An example of code snippet that will not fail is:
add $s1, $t0, $t1
add $s1, $t2, $s1 # Here the second operand is forwarded correctly
(3) Jumping to a branch target does not work. Example of code that fails:
addi $s1, $zero, 2
addi $s2, $zero, 2
beq $s1, $s2, exit
Code that will still work:
addi $s1, $zero, 10
addi $s2, $zero, 20
beq $s1, $s2, exit
2. [3 points] Consider the following assembly language code:
I0: ADD R4 = R1 + R0;
I1: SUB R9 = R3 – R4;
I2: ADD R4 = R5 + R6;
I3: LDW R2 = MEM[R3 + 100];
I4: LDW R2 = MEM[R2 + 0];
I5: STW MEM[R4 + 100] = R2;
I6: AND R2 = R2 & R1;
I7: BEQ R9 == R1, Target;
I8: AND R9 = R9 & R1;
Consider a pipeline with forwarding, hazard detection, and 1 delay slot for branches. The
pipeline is the typical 5-stage IF, ID, EX, MEM, WB MIPS design. For the above code, complete the
pipeline diagram below (instructions on the left, cycles on top) for the code. Insert the characters IF,
ID, EX, MEM, WB for each instruction in the boxes. Assume that there two levels of bypassing, that
the second half of the decode stage performs a read of source registers, and that the first half of the
write-back stage writes to the register file.
Label all data stalls (Draw an X in the box). Label all data forwards that the forwarding unit detects
(arrow between the stages handing off the data and the stages receiving the data). What is the final
execution time of the code?
Name: _____________________
Quiz for Chapter 4 The Processor
Page 3 of 30
T0 T1 T2 T3 T4 T5 T6 T7 T8 T9 T10 T11 T12 T13 T14 T15 T16 T17
I0
I1
I2
I3
I4
I5
I6
I7
I8
T0 T1 T2 T3 T4 T5 T6 T7 T8 T9 T10 T11 T12 T13 T14 T15 T16 T17
I0 IF ID EX ME
M
WB
I1 IF ID EX ME
M
WB
I2 IF ID EX ME
M
WB
Name: _____________________
Quiz for Chapter 4 The Processor
Page 4 of 30
I3 IF ID EX ME
M
WB
I4 IF ID X EX ME
M
WB
I5 IF X ID EX ME
M
WB
I6 X IF ID EX ME
M
WB
I7 IF ID EX ME
M
WB
I8 IF ID EX ME
M
WB
The final execution time of the code is 13 cycles.
3. [5 points] Structural, data and control hazards typically require a processor pipeline to stall. Listed
below are a series of optimization techniques implemented in a compiler or a processor pipeline
designed to reduce or eliminate stalls due to these hazards. For each of the following optimization
techniques, state which pipeline hazards it addresses and how it addresses it. Some optimization
techniques may address more than one hazard, so be sure to include explanations for all addressed
hazards.
(a) Branch Prediction
It addresses control hazards by guessing the outcome of a branch instruction and then speculatively
executes the instructions on one side of the branch to keep the pipeline moving. Predictions can be
made in hardware or in software by the compiler.
(b) Instruction Scheduling
It addresses structural hazards and data hazards. It addresses data hazards by either moving
instructions that are not dependent on an instruction, say A, before some instructions that depend on
A and thus avoiding the stall that would have occurred otherwise. It addresses structural hazards by
making sure instructions that use functional units that have limited number of instances are be
scheduled far apart from each other and there is no unnecessary stall due to this. It can be done in
hardware (superscalar processor) or statically by the compiler
(c) delay slots
It addresses control hazards. It helps to avoid a stall that would result due branch target identification
during the decode stage by scheduling the execution of some other instruction which anyway has to
execute irrespective of the branch condition.
Name: _____________________
Quiz for Chapter 4 The Processor
Page 5 of 30
(d) increasing availability of functional units (ALUs, adders etc)
It helps to avoid structural hazards. It is possible to run multiple instructions of the same type at the
same time if we have replicated functional units
(e) caches
It addresses data hazards. In particular, caches help to reduce memory latency and hence reduce the
load-use latency which in turn reduce the stall duration and improves execution time (by maintaining
pipeline steady state).
4. [6 points] Branch Prediction. Consider the following sequence of actual outcomes for a single static
branch. T means the branch is taken. N means the branch is not taken. For this question, assume that
this is the only branch in the program.
T T T N T N T T T N T N T T T N T N
(a) Assume that we try to predict this sequence with a BHT using one-bit counters. The counters in the
BHT are initialized to the N state. Which of the branches in this sequence would be mis-predicted?
You may use this table for your answer:
Predictor state before
prediction
Branch outcome Misprediction?
N T
T
T
N
T
N
T
T
T
N
T
N
T
T
T
N
T
N
Predictor state before
prediction
Branch outcome Misprediction?
N T Y
T T N
T T N
T N Y
N T Y
Name: _____________________
Quiz for Chapter 4 The Processor
Page 6 of 30
T N Y
N T Y
T T N
T T N
T N Y
N T Y
T N Y
N T Y
T T N
T T N
T N Y
N T Y
T N Y
(b) Now, assume a two-level branch predictor that uses one bit of branch history—i.e., a one-bit
BHR. Since there is only one branch in the program, it does not matter how the BHR is concatenated
with the branch PC to index the BHT. Assume that the BHT uses one-bit counters and that, again, all
entries are initialized to N. Which of the branches in this sequence would be mis-predicted? Use the
table below.
Predictor state before
prediction
BHR Branch outcome Misprediction?
N N T
T
T
N
T
N
T
T
T
N
T
N
T
T
T
N
T
N
Predictor state before
prediction
BHR Branch outcome Misprediction?
N N T Y
T T T Y
T T T N
T T N Y
N N T N
T T N N
Name: _____________________
Quiz for Chapter 4 The Processor
Page 7 of 30
N N T N
T T T Y
T T T N
T T N Y
N N T N
T T N N
N N T N
T T T Y
T T T N
T T N Y
N N T N
T T N N
(c) What is a return-address-stack? When is a return address stack updated?
A return address stack is a hardware mechanism used to predict the target of return-from-function-
call instructions. The return address stack is updated after either a call instruction or a return
instruction is predicted.
5. [16 points] The classic 5-stage pipeline seen in Section 4.5 is IF, ID, EX, MEM, WB. This pipeline is
designed specifically to execute the MIPS instruction set. MIPS is a load store architecture that
performs one memory operation per instruction, hence a single MEM stage in the pipeline suffices.
Also, its most common addressing mode is register displacement addressing. The EX stage is placed
before the MEM stage to allow it to be used for address calculation. In this question we will consider a
variation in the MIPS instruction set and the interactions of this variation with the pipeline structure.
The particular variation we are considering involves swapping the MEM and EX stages, creating a
pipeline that looks like this: IF, ID, MEM, EX, WB. This change has two effects on the instruction set.
First, it prevents us from using register displacement addressing (there is no longer an EX in front of
MEM to accomplish this). However, in return we can use instructions with one memory input
operand, i.e., register-memory instructions. For instance: multf_m f0,f2,(r2) multiplies the
contents of register f2 and the value at memory location pointed to by r2, putting the result in f0.
(a) Dropping the register displacement addressing mode is potentially a big loss, since it is the mode
most frequently used in MIPS. Why is it so frequent? Give two popular software constructs whose
implementation uses register displacement addressing (i.e., uses displacement addressing with non-
zero displacements).
Two popular software constructs that use register displacement addressing are:
• Use of arrays and loops stepping through them using an index variable
• Indirect jumps that are used for implementing switch..case constructs in a high level languages
may need to access a specific indexed entry in a jump table using register displacement mode.
(b) What is the difference between a dependence and a hazard?
An instruction A is said to be dependent on an instruction B if the A’s execution is determined by
some condition computed by B or if A uses some data value that is produced by B. A hazard is
situation which prevents the pipelined execution of an program and causes a stall. Hazards are usually
Name: _____________________
Quiz for Chapter 4 The Processor
Page 8 of 30
a consequence of having data dependencies between instructions, but it is possible for hazards to
manifest on an architecture even though intrinsically there are no dependences between instructions
due to limitations in the number of resources (registers/functional units).
(c) In this question we will work with the SAXPY loop.
do I = 0,N
Z[I] = A*X[I] + Y[I]
Here is the new assembly code.
0: slli r2,r1,#3 // I is in r1
1: addi r3,r2,#X
2: multf_m f2,f0,(r3) // A is in f0
3: addi r4,r2,#Y
4: addf_m f4,f2,(r4)
5: addi r4,r2,#Z
6: sf f4,(r4)
7: addi r1,r1,#1
8: slei r6,r1,r5 // N is in r5
9: bnez r6,#0
Using the instruction numbers, label the data and control dependences.
Data Dependencies:
Flow Dependencies: 0 → 1, 1 → 2, 2 → 3, 3 → 4, 0 → 3, 0 → 5, 5 → 6, 7 → 8, 8 → 9
Anti Dependences: 1 → 7, 4 → 5
Output Dependences: 3 → 5
(d) Fill in the pipeline diagram for code for the new SAXPY loop. Label the stalls as d* for data-hazard
stalls and s* for structural stalls. What is the latency of a single iteration? (The number of cycles
between the completion of two successive #0 instructions). For this question, assume that FP addition
takes 2 cycles, FP multiplication takes 3 cycles and that all other operations take a single cycle. The
functional units are not pipelined. The FP adder, FP multiplier and integer ALU are all separate
functional units, such that there are no structural hazards between them. The register file is written by
the WB stage in the first half of a clock cycle and is read by the ID stage in the second half of a clock
cycle. In addition, the processor has full forwarding. The processor stalls on branches until the
outcome is available which is at the end of the EX stage. The processor has no provisions for
maintaining “precise state”.
Name: _____________________
Quiz for Chapter 4 The Processor
Page 9 of 30
(e) In the pipeline for MIPS mentioned in the text, what is the reason for forcing non-memory
operations to go through the MEM stage rather than proceeding directly to the WB stage?
To facilitate pipelining by removing structural hazards, every instruction should access a structure at
most once and always in the same pipeline stage. The structure here is the register write port.
(f) Aside from the direct loss of register displacement addressing and the subsequent instructions
required to explicitly compute addresses, what are two other disadvantages of this sort of pipeline?
The branch penalty is longer since the EX and IF stages are now further away. In addition, load/ALU
stall that could not be corrected via forwarding in the original pipeline is now an ALU/load-store stall
that cannot be corrected via forwarding. There are also ISA problems with asymmetric operands which
violates the regularity and orthogonality principles.
(g) Reduce the stalls by pipeline scheduling a single loop iteration. Show the resulting code and fill in
the pipeline diagram. You do not need to show the optimal schedule for a correct response.
Here is an example. The key is that multf_m (which is a 3 cycle operation) is moved 3 instructions
ahead of addf_m. addf_m (which is a 2 cycle operation) remains 2 instructions ahead of sf. Notice, the
Name: _____________________
Quiz for Chapter 4 The Processor
Page 10 of 30
branch is still at the end, and no RAW dependences are violated, although one had to be resolved via
renaming.
0: slli r2,r1,#3 // I is in r1
1: addi r3,r2,#X
2: addi r4,r2,#Y
3: multf_m f2,f0,(r3) // A is in f0
4: addi r8,r2,#Z
5: addi r1,r1,#1
6: addf_m f4,f2,(r8)
7: slei r6,r1,r5 // N is in r5
8: sf f4,(r4)
9: bnez r6,#0
6. [8 points] A two-part question.
(Part A) Dependence detection
This question covers your understanding of dependences between instructions. Using the code below,
list all of the dependence types (RAW, WAR, WAW). List the dependences in the respective table
(example INST-X to INST-Y) by writing in the instruction numbers involved with the dependence.
I0: A = B + C;
I1: C = A – B;
I2: D = A + C;
I3: A = B * C * D;
I4: C = F / D;
I5: F = A ˆ G;
I6: G = F + D;
RAW Dependence WAR Dependence WAW Dependence
From Instr To Instr From Instr To Instr From Instr To Instr
Name: _____________________
Quiz for Chapter 4 The Processor
Page 11 of 30
RAW Dependence WAR Dependence WAW Dependence
From Instr To Instr From Instr To Instr From Instr To Instr
I0 I1 I0 I1 I0 I3
I0 I2 I1 I3 I1 I4
I1 I2 I2 I4
I3 I5 I3 I4
I2 I3 I4 I5
I1 I3 I5 I6
I2 I4
I3 I5
I5 I6
(Part B) Dependence analysis
Given four instructions, how many unique comparisons (between register sources and destinations)
are necessary to find all of the RAW, WAR, and WAW dependences. Answer for the case of four
instructions, and then derive a general equation for N instructions. Assume that all instructions have
one register destination and two register sources.
For four instructions, the number of unique comparisons:
(2(3) + 2(2) + 2(1)) + (2(3) + 2(2) + 2(1)) + (3 + 2 + 1) = 30
The first summand is for RAW comparisons, the second summand is for WAR comparisons and the
last summand is for WAW comparisons.
The general equation for N instructions = (5*(n-1)*n)/2
7. [10 points] This is a three-part question about critical path calculation. Consider a simple single-
cycle implementation of MIPS ISA. The operation times for the major functional components for this
machine are as follows:
Component Latency
ALU 10 ns
Adder 8 ns
ALU Control Unit 2 ns
Shifter 3 ns
Control Unit/ROM 4 ns
Sign/zero extender 3 ns
2-1 MUX 2 ns
Memory (read/write) (instruction or data) 15 ns
PC Register (read action) 1 ns
PC Register (write action) 1 ns
Register file (read action) 7 ns
Register file (write action) 5 ns
Logic (1 or more levels of gates) 1 ns
Name: _____________________
Quiz for Chapter 4 The Processor
Page 12 of 30
Below is a copy of the MIPS single-cycle datapath design. In this implementation the clock cycle is
determined by the longest possible path in the machine. The critical paths for the different instruction
types that need to be considered are: R-format, Load-word, and store-word. All instructions have the
same instruction fetch and decode steps. The basic register transfer of the instructions are:
Fetch/Decode: Instruction <- IMEM[PC];
R-type: R[rd] <- R[rs] op R[rt]; PC <- PC + 4;
load: R[rt] <- DMEM[ R[rs] + signext(offset)]; PC <- PC +4;
store: DMEM[ R[rs] + signext(offset)] <- R[Rt]; PC <- PC +4;
(Part A)
In the table below, indicate the components that determine the critical path for the respective
instruction, in the order that the critical path occurs. If a component is used, but not part of the critical
path of the instruction (ie happens in parallel with another component), it should not be in the table.
The register file is used for reading and for writing; it will appear twice for some instructions. All
instruction begin by reading the PC register with a latency of 2ns.
Instruction
Type
Hardware Elements Used By Instruction
R-Format
Load
Store
Name: _____________________
Quiz for Chapter 4 The Processor
Page 13 of 30
Instruction
Type
Hardware Elements Used By Instruction
R-Format PC Instruction
Memory
Control Read
regs
ALU
control
ALU Control Reg
write
Load PC Instruction
Memory
Control Read
Reg
ALU
control
ALU Data
Memory
Control Reg
Write
Store PC Instruction
Memory
Control Read
Regs
ALU
control
ALU Read
Reg
Control Data
Memory
(Part B)
Place the latencies of the components that you have decided for the critical path of each instruction in
the table below. Compute the sum of each of the component latencies for each instruction.
Instruction Type Hardware Latencies For Respective Elements Total
R-Format 2 ns
Load 2 ns
Store 2 ns
Instruction Type Hardware Latencies For Respective Elements Total
R-Format 2 ns 15
ns
4 ns 7 ns 2 ns 10
ns
4 ns 5 ns
Load 2 ns 15
ns
4 ns 7 ns 2 ns 10
ns
15
ns
4 ns 5 ns
Store 2 ns 15
ns
4 ns 7 ns 2 ns 10
ns
7 ns 4 ns 15
ns
(Part C)
Use the total latency column to derive the following critical path information:
• Given the data path latencies above, which instruction determines the overall machine critical
path (latency)?
• What will be the resultant clock cycle time of the machine based on the critical path
instruction?
• What frequency will the machine run?
The store instruction determines the overall machine critical path latency since it has the maximum
latency.
The clock cycle time should be long enough to permit the critical path instruction to complete. So it
should be at least 66ns
The frequency of the machine would be (1/66) ns = 15.1 MHz
8. [18 points] This problem covers your knowledge of branch prediction.
The figure below illustrates three possible predictors.
• Last taken predicts taken when 1
• Up-Down (saturating counter) predicts taken when 11 and 10
Name: _____________________
Quiz for Chapter 4 The Processor
Page 14 of 30
• Automata A3 predicts taken when 11 and 10
Fill out the tables below and on the next page for each branch predictor. The execution pattern for the
branch is NTNNTTTN.
Table 1: Table for last-taken branch predictor
Execution
Time
Branch
Execution
State Before Prediction Correct or
Incorrect
State After
0 N 0
1 T
2 N
3 N
4 T
5 T
6 T
7 N
Execution
Time
Branch
Execution
State Before Prediction Correct or
Incorrect
State After
0 N 0 NT Correct 0
1 T 0 NT Incorrect 1
2 N 1 T Incorrect 0
3 N 0 NT Correct 0
4 T 0 NT Incorrect 1
5 T 1 T Correct 1
6 T 1 T Correct 1
7 N 1 T Incorrect 0
Name: _____________________
Quiz for Chapter 4 The Processor
Page 15 of 30
Table 2: Table for saturating counter (up-down) branch predictor.
Execution
Time
Branch
Execution
State Before Prediction Correct or
Incorrect
State After
0 N 01
1 T
2 N
3 N
4 T
5 T
6 T
7 N
Execution
Time
Branch
Execution
State Before Prediction Correct or
Incorrect
State After
0 N 01 NT Correct 00
1 T 00 NT Incorrect 01
2 N 01 NT Correct 00
3 N 00 NT Correct 00
4 T 00 NT Incorrect 01
5 T 01 NT Incorrect 10
6 T 10 T Correct 11
7 N 11 T Incorrect 10
Table 3: Table for Automata-A3 branch predictor.
Execution
Time
Branch
Execution
State Before Prediction Correct or
Incorrect
State After
0 N 01
1 T
2 N
3 N
4 T
5 T
6 T
7 N
Execution
Time
Branch
Execution
State Before Prediction Correct or
Incorrect
State After
0 N 01 NT Correct 00
1 T 00 NT Incorrect 01
2 N 01 NT Correct 00
3 N 00 NT Correct 00
4 T 00 NT Incorrect 01
5 T 01 NT Incorrect 11
6 T 11 T Correct 11
7 N 11 T Incorrect 10
Calculate the prediction rates of the three branch predictors:
Name: _____________________
Quiz for Chapter 4 The Processor
Page 16 of 30
Predictor Prediction Accuracy
Last-taken
Up-Down
Automata-A3
Predictor Prediction Accuracy
Last-taken 0.5
Up-Down 0.5
Automata-A3 0.5
9. [3 points] Pipelining is used because it improves instruction throughput. Increasing the level of
pipelining cuts the amount of work performed at each pipeline stage, allowing more instructions to
exist in the processor at the same time and individual instructions to complete
at a more rapid rate. However, throughput will not improve as pipelining is increased indefinitely.
Give two reasons for this.
Pipelining has a fixed (or relatively fixed) absolute overhead per stage which results from latch
overhead and clock/data skew. This means that the latency of a pipeline stage cannot be driven to zero.
Second, increasing the pipeline depth lengthens hazard penalties, increasing the CPI. For instance,
increasing the depth of the pipeline between the fetch and execute stage increases the branch mis-
prediction penalty.
10. [3 points] Forwarding logic design. For this problem you are to design a forwarding unit for a 5-
stage pipeline processor. The forwarding unit returns the value to be forwarded to the current
instruction. There are three places that the values for register RS and register RT can come from:
decode stage (register file), memory stage, and write-back stage.
The write-back and memory stage information consists of: _INDEX- explaining which inflight register
index is to be written _VALUE- the value that is to be written _ENABLE- whether or not the
instruction in the stage is writing.
Name: _____________________
Quiz for Chapter 4 The Processor
Page 17 of 30
The decode stage simply states the register index (for RS and RT) and the corresponding register value
from the register file.
Generally three values could exist, one of which the forwarding unit should choose for each of the RS
and RT register value requests. The memory stage has value MEM, the write-back stage has value WB,
and the register file has value RS-REG or RT-REG.
Using the table below which contains information about all of the instruction stages, indicate which
value should be forwarded to the current instruction: MEM, WB, RS-REG, or RT-REG. Each line
represents a Forwarding unit evaluation; there is no connection between evaluation lines in the table.
You do not need to worry about hazard detection, only value bypassing.
Mem Stage Write-Back Stage Register Stage RS
Value
RT
Value
Evaluation Index Write Index Write RS-Index RT-Index
0 5 1 23 0 6 7
1 7 0 16 1 16 8
2 10 1 10 1 11 10
3 17 0 12 1 12 12
4 19 0 19 0 19 25
Mem Stage Write-Back Stage Register Stage RS
Value
RT
Value
Evaluation Index Write Index Write RS-Index RT-Index
0 5 1 23 0 6 7 RS-REG RT-REG
1 7 0 16 1 16 8 WB RT-REG
2 10 1 10 1 11 10 RS-REG MEM
3 17 0 12 1 12 12 WB WB
4 19 0 19 0 19 25 MEM RT-REG
11. [12 points] Consider a MIPS machine with a 5-stage pipeline with a cycle time of 10ns. Assume
that you are executing a program where a fraction, f, of all instructions immediately follow a load upon
which they are dependent.
(a) With forwarding enabled what is the total execution time for N instructions, in terms of f ?
When pipeline is filled,
(1 – f)*N instructions take 1 cycle
f*N instructions take 2 cycles (including 1 cycle for load-use stall)
Total cycles = (1-f)*N + 2*f*N + 4 (then number of cycles to fill the pipeline)
Total time = 10 *(N*(1+f) + 4)
(b) Consider a scenario where the MEM stage, along with its pipeline registers, needs 12 ns. There are
now two options: add another MEM stage so that there are MEM1 and MEM2 stages or increase the
cycle time to 12ns so that the MEM stage fits within the new cycle time and the number of pipeline
stages remain unaffected. For a program mix with the above characteristics, when is the first option
better than the second. Your answer should be based on the value of f.
Let us ignore the fill cycles to simplify the calculations.
Option 1 : Time = ((1-f)*N + 3*f*N) * 10 = (1 + 2*f)*10*N
(additional load-use latency contributes to 1*f*N)
Name: _____________________
Quiz for Chapter 4 The Processor
Page 18 of 30
Option 2 : Time = ((1-f)*N + 2*f*N)*12 = (1 + f)* 12*N
Option 1 is better when (1+2*f)*10x < (1+f)*12*x
f < ¼
(c) Embedded processors have two different memory regions – a faster scratchpad memory and a
slower normal memory. Assume that in the 6 stage machine (with MEM1 and MEM2 stages), there is a
region of memory that is faster and for which the correct value is obtained at the end of the MEM1
stage itself while the rest of the memory needs both MEM1 and MEM2 stages. For the sake of
simplicity assume that there are two load instructions load.fast and load.slow that indicate which
memory region is accessed. If 40% of the fraction f mentioned above get their value from the fast
memory, how does the answer to the previous question change ?
Option 1 : Time = ((1-f)*N + 0.4*2*f*N + 0.6*3*f*N)*10
= (1 + 1.6*f)*10*N
Option 1 is better when
(1 + 1.6*f)*10*N < (1 + f)*12*N
f < ½
12. [10 points] You are given a 4-stage pipelined processor as described below.
• IF: Instruction Fetch
• IDE: Instruction Decode, Register Fetch, ALU evaluation, branch instructions change PC,
address calculation for memory access.
• MEM: memory access for load and store instructions.
• WB: Write the execution result back to the register file. The writeback occurs at the 2nd half of
the cycle.
Assume the delayed branching method discussed in Section 4.3. For the following program, assume
that the loop will iterate 15 times. Assume that the pipeline finishes one instruction every cycle except
when a branch is taken or when an interlock takes place. An interlock prevents instructions from being
executed in the wrong sequence to preserve original data dependencies. Assume register bypass from
both the IDE output and the MEM output. Also assume that r2 will not be needed after the execution
returns.
Name: _____________________
Quiz for Chapter 4 The Processor
Page 19 of 30
(a) Is there any interlock cycle in the program? If so, perform code reordering on the program and
show the new program without interlock cycle.
There is an interlock cycle in the program resulting out of a dependence between instruction C and D,
for which there is a stall of 1 cycle. By reordering the code in the following way:
A ADD r3 <- 0
B LOAD r1 <- M(0200)
C Loop: LOAD r2 <- M(0208 + r1)
E SUB r1 <- r1 – 4
D ADD r3 <- r2 + r3
F BRANCH != PC <- Loop if r1 != 0
G NOP a delay slot
H STORE M(0204) <- r3
I RETURN return from function
J NOP a delay slot
the interlock cycle can be eliminated
(b) Derive the total number of cycles required to execute all instructions before and after you
eliminated the interlock cycle.
The number of cycles to execute before the transformation = 4 + 2 + 6*15 + 3 = 99 cycles. The number
of cycles after the transformation = 4 + 2 + 5*15 + 3 = 84 cycles
(c) Fill the delay slots. Describe the code reordering and/or duplication performed. Show the same
program after delay slot filling. Recall that RETURN is also a branch instruction. Use a ’ to mark the
new copy of a duplicated instruction. For example, if you duplicated D, name the new copy D’.
A ADD r3 <- 0
B LOAD r1 <- M(0200)
C Loop: LOAD r2 <- M(0208 + r1)
E SUB r1 <- r1 – 4
F BRANCH != PC <- Loop if r1 != 0
D ADD r3 <- r2 + r3
I RETURN return from function
H STORE M(0204) <- r3
(d) Derive the total number of cycles required to execute all instructions after you filled the delay slots.
The total number of cycles after filling in delay slots = 4 + 2 + 4*15 + 2 = 68 cycles
13. [3 points] Using any ILP optimization, double the performance of the following loop, or explain
why it is not possible. The machine can only do one branch per cycle, but has infinite resources
otherwise.
r1 = ... ; r1 is head pointer to a linked list
r3 = 0
LOOP:
r2 = M[r1 + 8]
r3 = r3 + r2
r1 = M[r1]
branch r1 != 0, LOOP
... = r3 ; r3 is used when loop complete
Name: _____________________
Quiz for Chapter 4 The Processor
Page 20 of 30
By performing the following code reordering we can avoid a 1-cycle stall due to a dependence between
the first and second instructions of the loop:
r1 = ... ; r1 is head pointer to a linked list
r3 = 0
LOOP:
r3 = r3 + r2
r2 = M[r1 + 8]
r1 = M[r1]
branch r1 != 0, LOOP
... = r3 ; r3 is used when loop complete
14. [10 points] Consider the datapath below. This machine does not support code with branch delay
slots. (It predicts not-taken with a 1-cycle penalty on taken branches.) For each control signal listed in
the table below, determine its value at cycles 3 through 9, inclusive. Also, show the instruction
occupying each stage of the pipeline in all cycles. (Assume the IF/ID write-enable line is set to the
inverse of the Stall signal.)
The initial state of the machine is:
PC = 0
All pipeline registers contain 0s
All registers in the register file contain 0s.
The data memory contains 0s in all locations
The instruction memory contains:
00: addiu $3, $zero, 4
04: lw $4, 100($3)
08: addu $2, $4, $3
0C: beq $4, $zero, 0x14
10: addiu $3, $3, 1
14: addu $2, $2, $3
all other locations contain 0
Use data forwarding whenever possible. All mux inputs are numbered vertically from “top” to
“bottom” starting at 0 as you look at the datapath in the proper landscape orientation. Also, the values
for ALUOp are:
Value Desired ALU Action
00 Add
01 Subtract
10 Determine by decoding funct field
Instruction formats:
Name: _____________________
Quiz for Chapter 4 The Processor
Page 21 of 30
Ti
m
e
P
C
W
ri
te
IF
.F
lu
s
h
B
ra
n
c
h
S
ta
ll
A
L
U
S
rc
A
L
U
O
p
R
e
g
D
s
t
F
o
rw
a
rd
A
F
o
rw
a
rd
B
M
e
m
R
e
a
d
M
e
m
W
ri
te
M
e
m
to
R
e
g
R
e
g
W
ri
te
IF ID EX M WB
00: addiu -- -- -- -- 0
1 0 0 0 0 00 0 00 00 0 0 0 0
04: lw 00: addiu -- -- -- 1
1 0 0 0 0 00 0 00 00 0 0 0 0
08: addu 04: lw 00: addiu -- -- 2
1 0 0 0 1 00 0 00 00 0 0 0 0
3
4
5
6
7
8
9
Ti
m
e
P
C
W
ri
te
IF
.F
lu
s
h
B
ra
n
c
h
S
ta
ll
A
L
U
S
rc
A
L
U
O
p
R
e
g
D
s
t
F
o
rw
a
rd
A
F
o
rw
a
rd
B
M
e
m
R
e
a
d
M
e
m
W
ri
te
M
e
m
to
R
e
g
R
e
g
W
ri
te
IF ID EX M WB
00: addiu -- -- -- -- 0
1 0 0 0 0 00 0 00 00 0 0 0 0
04: lw 00: addiu -- -- -- 1
1 0 0 0 0 00 0 00 00 0 0 0 0
08: addu 04: lw 00: addiu -- -- 2
1 0 0 0 1 00 0 00 00 0 0 0 0
Name: _____________________
Quiz for Chapter 4 The Processor
Page 22 of 30
0C: beq 08: addu 04: lw 00: addiu -- 3
0 0 0 1 1 00 0 10 0 X 0 X 0
0C: beq 08:addu LOAD-USE STALL (NOP) 04:lw 00:addiu 4
1 0 0 0 X X X X X 1 0 1 1
10: addiu 0C: beq 08: addu NOP 04: lw 5
1 1 1 0 1 10 1 01 00 X 0 0 1
14: addu TAKEN BR (NOP) 0C : beq 08: addu 6
1 0 0 0 X X X X X X 0 X 0
18:nop 14: addu NOP 0C : beq 08: addu 7
1 0 0 0 X XX X X X X 0 1 1
1c:nop 18:nop 14: addu NOP 0C : beq 8
1 0 0 0 1 10 1 00 00 X 0 X 0
20:nop 1c:nop 18:nop 14: addu NOP 9
1 0 0 0 X XX X X X X 0 X 0
15. [6 points] Consider the following data path diagram:
(a) Discuss the functionality of the RegDst and the ALUSrc control wires.
The RegDst control signal is used to specify the register destination number for instructions that have
a register as their destination operand (rd).
The ALUSrc control signal is used to choose between either the second register operand from the
instruction or the sign-extended lower 16 bits of the instruction.
Name: _____________________
Quiz for Chapter 4 The Processor
Page 23 of 30
(b) Next, modify the diagram to indicate the datapath changes (and any additional multiplexing)
needed to provide bypassing from EX to EX for all possible RAW hazards on arithmetic instructions.
How does ALUSrc change when bypassing is added?
The ID/EX and EX/MEM latches will have a new forwarding unit between them directing the outputs
of the EX stage into the MUX’s that feed the inputs into the ALU. The ALUSrc control signal will not
have to be modified since it is already the output from one of the MUX’s. The modification (only the
relevant part of the diagram is shown below) is as follows:
16. [3 points] Imagine an instruction whose function is to read four adjacent 32-bit words from
memory and places them into four specified 32-bit architectural registers. Assuming the 5-stage
pipeline is filled with these instructions and these instructions ONLY, what is the minimum number of
register file read and write ports that would be required?
The minimum number of write ports is four and the minimum number of read ports is two (in this
case an additional read port is to read the register that holds the memory address)
17. [12 points] Pipelining and Bypass. In this question we will explore how bypassing affects program
execution performance. To begin consider the standard MIPS 5 stage pipeline. For your reference,
refer to the figure below. For this question, we will use the following code to evaluate the pipeline’s
performance:
1 add $t2, $s1, $sp
2 lw $t1, $t1, 0
3 addi $t2, $t1, 7
4 add $t1, $s2, $sp
Name: _____________________
Quiz for Chapter 4 The Processor
Page 24 of 30
5 lw $t1, $t1, 0
6 addi $t1, $t1, 9
7 sub $t1, $t1, $t2
(a) What is the load-use latency for the standard MIPS 5-stage pipeline?
The load use latency for the standard MIPS 5-stage pipeline is 1 cycle.
(b) Once again, using the standard MIPS pipeline, identify whether the value for each register operand
is coming from the bypass or from the register file. For clarity, please write REG or BYPASS in each
box.
Instruction Src Operand 1 Src Operand 2
1
2 N/A
3 N/A
4
5 N/A
6 N/A
7
Instruction Src Operand 1 Src Operand 2
1 Register File Register File
2 Register File N/A
3 Bypass N/A
4 Register File Register File
5 Bypass N/A
6 Bypass N/A
7 Bypass Register File
(c) How many cycles will the program take to execute on the standard MIPS pipeline?
It takes 13 cycles to execute on the standard MIPS pipeline
(d) Assume, due to circuit constraints, that the bypass wire from the memory stage back to the execute
stage is omitted from the pipeline. What is the load-use latency for this modified pipeline?
The load use latency for this pipeline is 2 cycles
(e) Identify whether the value for each register operand is coming from the bypass or from the register
file for the modified pipeline. For clarity, please write REG or BYPASS in each box.
Instruction Src Operand 1 Src Operand 2
1
2 N/A
3 N/A
4
5 N/A
6 N/A
7
Name: _____________________
Quiz for Chapter 4 The Processor
Page 25 of 30
Instruction Src Operand 1 Src Operand 2
1 Register File Register File
2 Register File N/A
3 Register File N/A
4 Register File Register File
5 Bypass N/A
6 Register File N/A
7 Bypass Register File
(f) How long does the program take to execute on the modified pipeline?
It takes 15 cycles to execute on the modified pipeline.
18. [3 points] Scheduling. “A schedule defends from chaos and whim.”—Annie Dillard
Consider this pseudo-assembly snippet:
1: mov r1 = 0 ;; iteration count i
2: mov r2 = 0 ;; initialize x
loop:
3: sll r3 = r1, 2 ;; r3 = r1*4
4: lw r4 = A(r3) ;; load A[i]
5: add r2 = r2, r4 ;; x += A[i]
6: add r1 = r1, 1 ;; increment counter
7: bne r1, 1024, loop ;; backwards branch
Assume you have a machine with infinite resources (i.e. infinite width, infinite instruction window,
infinite number of functional units, infinite rename resources, infinite number of
outstanding/overlapping loads, etc.), and that it is fully pipelined so that all normal instructions take 1
cycle. Loads which hit in the cache also take 1 cycle, but loads that miss take 10 cycles. Also assume
perfect branch prediction.
(a) Show the dynamic schedule of the instructions of the first two iterations of the loop in the table
below assuming that the load misses in the cache in even iterations (r1=0,2,. . . ) and hits in the cache
in odd iterations (r1=1,3,. . . ). Be sure to indicate the loop iteration each instruction is associated with.
For example, if instruction 5 of iteration 7 can run in cycle 3, then you would write “5.7” in one of the
boxes in cycle 3’s row. Note that the first cycle has been filled in for you and that the cells in the table
are more than you need.
Cycle Instructions
1 1 2
2
3
4
5
6
7
8
9
10
11
Name: _____________________
Quiz for Chapter 4 The Processor
Page 26 of 30
12
13
14
15
16
17
18
Cycle Instructions
1 1 2
2 3.1
3 4.1
4 4.1
5 4.1
6 4.1
7 4.1
8 4.1
9 4.1
10 4.1
11 4.1
12 4.1
13 5.1 6.1
14 7.1
15 3.2
16 4.2
17 5.2 6.2
18 7.2
19. [3 points] Prediction and Predication. “When a decision has to be made, make it.” –General
George Patton
(a) Consider the following piece of code:
for(i=0; i<1000000; i++){
a = random(100);
if(a >= 50){
…
}
}
Assume that random(N) returns a random number uniformly distributed between 0 and N-1
inclusive. Consider the branch instruction associated with the if statement. Is there a type of branch
predictor that predicts this branch well? Explain your answer.
A predictor which constantly predicts Taken (or Not Taken) is likely to be right half of the times here.
Since a is uniformly distributed between 0 and 99, the probability that it is greater than 50 is 0.5. So
one would expect that in a large number of trials, about half the number of times the branch would be
taken. Any other predictor is likely to be of no use since the possibility of whether a particular instance
of branch is taken is independent of all other instances of the branch.
Name: _____________________
Quiz for Chapter 4 The Processor
Page 27 of 30
(b) Predication can eliminate all forward conditional branches in a program. The backward branches
in a program are, typically, associated with loops and hence are mostly taken. So it is possible to
eliminate all forward branches and statically predict the backward branches as Taken and this would
get rid of the complex branch predictors in a machine. But the Itanium processor which has hardware
support for predication still retains a complex two level branch predictor. Explain why this is the case.
Firstly eliminating all forward branches can result in a lot of dynamic instructions to be wastefully
executed due to misspeculated execution of predicated instructions. Secondly in case of nested loops,
having a two level branch predictor can help in accumulating histories specific to each branch and be
able to learn each backward branch’s periodicity accurately by not letting the patterns of the two
branch instructions to interfere with each other.
20. [10 points] Compilers are useful (occasionally). A common loop in scientific programs is the so-
called SAXPY loop:
for (i=0;i